Genuine Bosch Hall Effect Sensor BMW R Oilhead ; 12 11 7 673 277 BOIgnSen-R277

Description

Euro MotoElectrics . . . Your Source for BMW Motorcycle Parts ! ! !
Part #: BOIgnSen-R277 (6-pin rectangular oval connector)
BOSCH Original Equipment New Hall Effect Ignition Trigger Sensor with 6-pin rectangular oval "plug-in" harness connector.
Replaces failed magnetic hall-effect phase sensors and delicate deteriorated wires or insulation with an improved insulated PTFE cable.
Vehicle Manufacturer:
BMW
Application:
R850, R1100S 1998-04, R1150GS 1999-2004, R1150R 2001-04, R1200 1997-04
Make/Model:
BMW : R1100S, R1150GS, R, RS, RT, R1200
Model Years:
1996 to 2006
Manufacturer #:
12 11 7 673
277
Power Rating:
Original Equipment - NEW
(See APPLICATION TABLE below to verify vehicle fitment )
If you need the sensor with the flat - single-file plug (BMW Part # 12 11 2 306
137
)
Original Equipment :
Bosch
Refer to "Additional Photos" for connector plug configuration in comparison to "R137"
The total swing in timing on the R850, R1100, and R1150 is 5°, the bike will start and run well at either end of the slotted hole.
Important Installation Note:
There is a two prong tab on the alternator pulley that engages with the groove on the crankshaft. This attachment should be bonded when torquing the pulley bolt to avoid damage to the hall effect ignition sensor.
Verify that your rotor pulley is aligned correctly with the crankshaft before installing the hall effect sensor.
If the installation of the hall sensor is done with the rotor misaligned you could destroy the sensor, when attempting start it.
Take care not to bend the locating tab on the rotor.
Ensure the rotor is properly located back into the slot on the end of the crank shaft.
Installation Instructions
1. Disconnect and insulate the battery ground lead (IMPORTANT)
2. Remove the existing hall sensor (refer to BMW repair manual)
3. Install TDC pin to lock the flywheel to the clutch housing (EME Part #
BMW-TDCpin)
4. Set the hall-effect timing position using a hall tester Part #
EDL-MiniHT-R277
- LED must be triggered at TDC
5. Connect the battery ground lead
6. Switch on the ignition but do not start the engine
7. Open the throttle fully twice - this will synchronize the motronic control unit with the new hall sensor
Part # BOIgnSen-R277
BWM # 12 11 7 673 277
Model
Year
R850C
01/1997 - 09/2000
R850R
99-07 11/1999 - 07/2007
R850RT
00-06 06/2000 - 02/2006
R1100S
01/1997 - 09/2004
R1100S
12/1996 - 07/2005
R1150 ADV
07/2001 - 09/2005
R1150GS
09/1998 - 11/2003
R1150R
03/2000 - 02/2006
R1150R
11/1999 - 06/2006
R1150R Rockster
03/2002 - 07/2005
R1150RS
11/2000 - 01/2004
R1150RS
11/2000 - 11/2004
R1150RT
01/2000 - 03/2006
R1150RT
02/2000 - 02/2006
R1200 Montauk
10/2002 - 10/2004
R1200C
02-04 10/2002 - 07/2004
R1200C
96-03 04/1996 - 05/2003
R1200C
96-03 06/1996 - 05/2003
R1200C I
00-03 05/2000 - 05/2003
R1200C I
00-03 09/2000 - 05/2003
R1200C I
03-04 02/2003 - 08/2004
R1200C I
03-04 10/2003 - 05/2004
R1200CL
10/2001 - 07/2004
Returns: All returns must be in original packaging where applicable and must NOT have been installed. Previously installed parts are NOT returnable. Returns must be in re-sellable condition. Please contact us if you are having problems with any item you have purchased from us.
Thank you for shopping with Euro MotoElectrics. Your complete satisfaction is our goal. Please contact us if you are not completely satisfied with your purchase, prior to leaving feedback. We will make every effort to ensure complete satisfaction. We appreciate your business. TEAM EME~
On Aug-12-17 at 17:15:06 PDT, seller added the following information: